Fusion 21 Color LED Lighting Accessories

Fusion Multi-Color LED Lighting Accessories

You can expand your Fusion Multi-Color System anytime by just purchasing an extra LED Strip, Splitter and maybe Extension Cable. 

You will need a Splitter for each extra LED Strip that you purchase.

The 12" and 24" extension cables are great for installing LED Strips all the way up front or in back where a little extra routing is required.  When using a lot of extra lights we strongly suggest using at least a couple of 12" ext. cables. then Install splitters on the end of the extension cable so all of your cables do not end in one location.  This will make a lot neater job.
Fusion 21 color LED Strip POD's have 34" to 40" cables.

Push Button Switches are used as a convenient power disconnect to reduce power consumption during hibernation or as a switch to be used as a master reset.  We strongly suggest using a switch in the power circuit to the CPU.

The 3 POD 6 foot extension routes three cables down to one and back to three and is six feet long.  Male ends which plug into the CPU is staggered according to 3 zone lengths.  Designed for large bikes and trikes.

Fusion Rim Lights connect to the CPU through a 72" Cable (one required per wheel).  The Rim Lights easily mount on the brake caliper and provide 360 degrees of light giving an even disbursement of glow around the entire rim.  The rim light requires 1/2 inch of clearance between the caliper and wheel or spokes, so it will fit on most every bike.  Mounts with double sided tape like rest of the lights and is 2 1/8" in Diameter.  You will need at least a 12" and most likely a 24" ext. cable for installation of Rim Lights.
Rim light shown below.


Power Amplifier:  Increases the Amperage Output of a zone on the controller from 1.5 amps to 4.5 amps per zone.  Used for long runs with multiple lights on that specific zone (trailers are a good example).

Select the accessories you need above.

The Fusion L.E.D. Systems are the most complete way to quickly customize your motorcycle with LED’s, yet not spend a fortune.
The Fusion systems eliminate time consuming wiring of LED's and simply plug into a main control module that can create the wildest flash patterns.
Every Fusion system comes with a wireless remote, CPU, Flex-Tech LED's and Mounting Hardware.
Click here to view youtube video.

Features:
A multicolor, three zone, six line, plug-n-play CPU with wireless remote.
13 Flash Patterns (5 Music / Engine Thump Modes)
5 Speed Flash Driver
5 Levels of sound sensitivity
18 Colors, including million color mode & seven color mode.
Secondary Power Up Option

Modes:
1. Solid State: No Flashing. Includes five levels of light intensity adjustment feature.
2. Basic Flash: All LEDs flash on & off simultaneously. Includes light intensity adjust and flash speed adjust.
3. Breath Mode: LEDs gradually flash on and off; giving the impression your motorcycle is breathing. Includes light intensity adjust and flash speed adjust.
4. Scanning Mode: LED’s flash from front of bike toward the back, repeatedly. Includes light intensity adjust and flash speed adjust.
5. Strobe Mode: LED’s flash to give impression of strobing light. Includes light intensity adjust and flash speed adjust.
6. Chase Mode: LEDs flash on from front to back – and flash off from back to front repeatedly. Includes light intensity adjust and flash speed adjust.
7. Wave Ripple Mode: LEDs flash from center of bike outward. Includes light intensity adjust and flash speed adjust.
8. Running Mode: LEDs flash on and then off while moving from front to back – back to front of bike. Includes light intensity adjust and flash speed adjust.
9. Music Mode I: Flashes to base of stereo or engine noise in front to back pattern. Includes light intensity adjust and sound sensitivity adjust.
10. Music Mode II: Flashes to base of stereo or engine noise in back to front pattern. Includes light intensity adjust and sound sensitivity adjust.
11. Music Mode III: Flashes to base of stereo or engine noise in wave ripple pattern. Includes light intensity adjust and sound sensitivity adjust.
12. Music Mode IV: Flashes to base of stereo or engine noise in reverse wave ripple pattern. Includes light intensity adjust and sound sensitivity adjust.
13. Music Mode V: Flashes to base of stereo or engine noise in mode 2. Includes light intensity adjust and sound sensitivity adjust.

Water and Shock Proof. 
Low Power Requirements
Transmit range: 10 meters
One Year Limited Warranty!

EASY INSTALLATION:
This is positively one of the easiest light mods there is. 
All you need to do is hook up a fused power source (switch optional) to power up your lights.  The CPU is powered all the time (very low power consumption) unless a switch is installed.
Place the CPU somewhere in the rear (under seat, battery compartment, auxiliary tool box or other storage compartments you can find.  The Fusion Flexible LED Light Strips each have a 4' extension lead that is routed back to the desired CPU Output.  the Extension Leads also are covered with a protective black heat shrink, making them durable and unnoticeable. 
You will then just place one zone of LED's to the front of the bike running each extension cable back to the CPU and plugging in.  You will place more LED's in the middle of the bike for another zone and more LED's towards the rear of the bike for a third zone.  The effect is amazing and totally custom.  
The LED's are also flexible allowing you to bend and twist as necessary.

FOB Program Instructions:
Older CPU:  With the CPU turned off, press and hold the flash pattern button(button A) on the CPU and then press and hold button A (green button) on the remote until you hear three rapid chirps. 
Release both buttons and remote reprogramming is complete.
Newer CPU:  With the LED lights turned off, press and hold the circular design etched on the front of the CPU, just below the Fusion logo. Then press and hold the green button on the remote until you hear three rapid chirps. Release both buttons as soon you hear the CPU begin to chirp. Remote reprogramming is complete. If you hold the buttons after the 3 chirps have end, you will need to redo the remote programming sequence.