BackOFF Brake Hold Module

BackOFF Brake Hold Module

The Brake Hold Module connects to your bike’s electronic speed pick-up sensor (will not work with cable driven speedometers); to keep your brake lights on when you release your brakes but are still decelerating.
In addition, it will turn them on or keep them on when you are are stopped, even if you take your hands and feet off the brakes!
Designed to work with LED lights.

This compact solid state electronic module converts your ordinary brake lights into your choice of two attention getting visual alerting signals when you apply your brakes:  

User Selected Mode One:
Emit a visual signal of 4 short light flashes, followed by 1 long light flash (3.5 seconds). The signal automatically repeats itself as long as the brakes are applied. This pattern is not random, but has been selected because of its ability to retain following drivers attention.

User Selected Mode Two:
Emit a visual signal of 5 short flashes, followed by a steady on light that remains steady on as long as the brakes are applied.

Brake Alert:
If the Brake Hold Module is holding your brake lights on for you and you wish to gain the attention of someone behind you; simply press either brake and your brake lights will flash 5 times then return to steady on.

Easy Installation.

Mode One Installation for - 3 Short Flashes / 1 Long Flash (Repeat):

Step 1: Before you begin…make sure your brake lights are working properly.
Step 2: Locate brake light wire (leading to the vehicles center brake light).
Step 3: Cut and splice Module into brake light wire (see schematic above). 
Secure "Red Wire" from Module to wire leading from "Brake Light 
Switch". Secure "White Wire with Red Stripe" from Module to wire
leading to the brake light.
Step 4: Connect "Black Wire" to Ground.
Step 5: Connect “Orange Wire” to +12V Switched (This needs to be a power source that is only energized when the bike’s key switch is on; the bike’s tail light is usually a good place for this).
Step 6: Tap the “White Wire with Green Stripe” into your bike’s speed sensor wire (Speed Sensor Wire are typically located on the transmission and have 3 wires: Power, Ground and Speed Sensor).
Step 7: Secure BackOFF Brake Hold Module with included double-sided adhesive tape.

Mode Two Installation for - 5 Quick Flashes & Steady On:

Step 1: Before you begin…make sure your brake lights are working properly!
Step 2: Locate "brake light wire" (leading to the vehicles center brake light).
Step 3: Cut and splice Module into brake light wire (see schematic above). 
Secure "Red Wire" from Module to wire leading from "Brake Light 
Switch". Secure "Red Wire with White Stripe" from Module to wire
leading to the brake light.
Step 4: Connect "Black Wire" to Ground.
Step 5: Connect “Orange Wire” to +12V Switched (This needs to be a power source that is only energized when the bike’s key switch is on; the bike’s tail light is usually a good place for this).
Step 6: Tap the “White Wire with Green Stripe” into your bike’s speed sensor wire (Speed Sensor Wire are typically located on the transmission and have 3 wires: Power, Ground and Speed Sensor).
Step 7: Secure BackOFF Brake Hold Module with included double-sided adhesive tape.

Another wiring option is with a Duel LED license frame.  You can wire the top Brake LED to the Mode One output wire and the Bottom Brake LED to the Mode Two output wire.  This really gives a neat effect when the brakes are applied.  A jumper wire would need to be installed for the second License Frame LED to the BackOFF Unit.

Features:
**Your Bike MUST have Electronic Pick-Up Sensor**
Easy Installation. - Simply install the Brake-Hold Module™ in line with the wire leading to the brake light, connect to a switched power source and ground wire, and tap a wire into your bike’s speed sensor.
Large power capacity: - 12 volts DC, Maximum Capacity 10 Amps!
Compact size. - 2-1/4"L x 1-5/8"W x 5/8"H
Sealed Weather Resistant heat sink case.
Limited Warranty - One Year!